top of page

Navimow Replacement Blades

Genuine Segway replacement blades with their screws. Change the whole set about every 180 mowing hours for a clean cut that never tears the grass. $23.99 from an authorized Navimow service center.

lp-blade-assembly-plus-hero.jpg

★★★★★ What our Navimow owners say

“Zippy Lawnz brought a mower and tested it on my property. So no anxiety. I ordered one on the spot. A few days later Paul brought the new mower, did a thorough installation and mapping and it's been working like a charm ever since.” — Harry Miller, verified buyer of the Navimow X430

The Navimow replacement blades guide

Fresh blades are the cheapest way to make a robot-mowed lawn look better. This is Segway's replacement blade assembly, blades with their screws, for doing the swap yourself. Below is when to change them, how to do it in about ten minutes, and what we learned testing blades on our own mowers.


Navimow blade replacement, and our test of cheap titanium-coated blades


How often

  • About every 180 hours of mowing. That's about a month if the mower runs six hours a day, or about four months at an hour and a half a day. My Zippy counts the hours for you.

  • Sooner with sandy soil (the biggest blade killer), sticks, pine cones or acorns, wet heavy grass, or a big yard.

  • The sign you're late: white, frayed tips a day after mowing and a gray-brown cast across the lawn. It isn't disease; it's dull blades. More in the ⅓ rule and blade care.

  • On a Terranox, we change discs every four weeks in season, by the calendar.


Navimow discs spin both ways and each blade pivots, so both edges get used. That roughly doubles a blade's life, and it's why the rest of this guide matters.



How to change them

  1. Turn the mower off and take it off the dock.

  2. Flip it onto a towel or a piece of cardboard.

  3. Swap the whole set, never one or two blades. A mixed set unbalances the disc.

  4. Clean the disc and check it for cracks. A cracked or bent disc gets replaced, not re-bladed.

  5. Fit new blades with new screws. The screw is the part that fails: it wears at the shoulder where the blade pivots. Never reuse them.

  6. Snug, not tight. Each blade must swing freely. Overtightening stops the pivot.

  7. Flip it back and run a spin test before it goes out.


New screws, snug not tight, and make them swing. Full walk-through: Navimow blade replacement.


Removing a Navimow X4 cutting disc with a screwdriver
Removing an X4 disc with a hand screwdriver.

Navimow cutting disc with fresh blades installed
A clean disc with a fresh set of blades.


Don't

  • Don't sharpen them. Sharpening changes the balance, and an unbalanced disc vibrates and wears out the bearings.

  • Don't reuse the screws.

  • Don't throw loose blades in the trash. They're sharps: tape them together or put them in a rigid container.



Three ways to get more from your blades

  • The 18-blade setup. Each X4 disc has three extra factory holes under its cover, so you can go from 6 to 9 blades per disc, 50% more cutting edge. It takes 10 to 15 minutes and one OEM pack; afterwards raise the cut height a setting or two and re-check obstacles. How to do it.

  • A spare set of discs with blades already fitted turns a 20-minute job into a 2-minute swap: Cutting Discs with blades installed.

  • The 14-Blade Titanium Cutting Discs change blades with four screws per plate: the titanium disc guide.


Navimow has hidden blade slots: here's how to use them


OEM, cheap titanium-coated, or hardened titanium?

We put a cheap titanium-coated set (ordinary stainless steel under a thin gold coating) against the stock Segway blades with a laser edge reader, a scale and a month of mowing. The OEM blades were sharper new, sharper worn, and about 25% heavier. Hardened titanium blades, like the ones on our 14-blade discs and in our 70-blade pack, are a different product: heat-hardened stainless steel with a titanium coating. Whatever you run, the change interval matters more than the brand. See the test.


We tested titanium Navimow blades vs OEM


Works with these blades



Blade questions we hear most

How often should I change Navimow blades?

About every 180 hours of mowing, sooner on sandy soil or a lawn with sticks and acorns.

Do I really need new screws every time?

Yes. The screw is the part that wears and fails, at the shoulder where the blade pivots.

Can I sharpen the old blades?

No. Sharpening unbalances the disc, and the vibration wears out the bearings.

Which mowers do they fit?

Tell us your model before you order if you're not sure. Call or text us at 410-725-7500.



More Zippy Lawnz product guides


Robot mowers

Snow

Docking, power and gates

Blades, discs and cut quality

Antenna and signal



Why buy Navimow parts from Zippy Lawnz

We are an authorized Segway Navimow dealer and service center, not a warehouse. We install and repair these mowers ourselves, so we can tell you exactly what fits yours. Not sure? Call or text 410-725-7500 and a real person will answer. Every owner also gets free monthly live training.

Blades and discs for your Navimow

More Zippy Lawnz best sellers

The mowers and parts our customers order most, each one sold, set up and supported by Zippy Lawnz.

Zippy Delmarva
elizabeth@zippylawnz.com
call or text 410-226-6705 

Zippy PA, NJ & DE
paul@zippylawnz.com
call or text 410-725-7500

Zippy Cape Charles, VA
zippy@zippylawnz.com
call or text 410-725-7500

Zippy West
wgolde@zippylawnz.com
call or text 720-251-1446

Zippy Steamboat
matthew@zippylawnz.com
call or text 610-585-6879

  • Reddit
  • Instagram
  • Facebook
  • Youtube
bottom of page